INSTALASI PENGKABELAN JARINGAN STRAIGHT

Bismillahirrahmanirrahim, Assalamualaikum warahmatullahi wabarakatuh How are you all? Hopefully we are all always in good health and in good health Amen, amen, ya Allah, ya rabbal alamin Well, on this occasion we will learn together how to do network connection installation, namely to do connection in a straight and crossover way

for materials about the two types of cables, you can read it first or look at the materials about what is a series type of cable and also crossover, this time I will focus on discussing how to build a network cable installation, even though

the tools needed for us to install the network cables are the first you must have a cable yes it is mandatory, this is a network cable or we call it a UTP, yes, where it has ends 1 and ends 2 which we will arrange later the color then there is another RG45 connector like this, there is one that is white, there is one that is red, yes

then this will be connected to the network cable then we also have to prepare crimping tools which will be used first to remove the cable and also to unite the cable with the LG45 connector

and finally we have to have this cable tester this cable tester is used to do cable testing after we combine it with the RG45 later we check whether the installation we do has succeeded or not whether the color of the light that appears is appropriate or not so this is very important for doing the test

Okay, after that, maybe it's okay, this is just a spare, this is also a spare, if later the tool doesn't work properly and I also prepare 4 RG45 connectors so that later every failure, maybe we still have a spare to try

that's all for the beginning, later we will continue for the network wiring material keep following this video and watch until the end hopefully the material is easy for us all okay, next thing we have to do is do the removal of the cable, more or less maybe this distance

for safety, maybe about one and a half books, we peel it first, how do we put it in the part that has a hole like this, we put it in here like this, then we turn it automatically, it will be peeled off like this, okay, even if we just remove this one,

that's the first thing we do the same thing we put it in here then we turn it will be completely removed we just pull it like this if it's done there are four cables that are wrapped together we separate them first one with the other

*Mumbling*

after we separate all these small cables, more or less 8, we straighten it like this

make sure everything is straight, no curly so later when we arrange it, it will be easier like this, more or less like this you can do the same thing on the other end make sure it's straight, no curly

I will do the same thing at the end of the first session, we will meet again in the cable structure arrangement session. What we will do now is to arrange the cable in a straight line.

Stretching means the arrangement of the cable at the end of the first and the end of the second is the same. So it's not different. Stretching means straight. We will do the arrangement together on this end cable. Later it will be continued with this end cable. The steps are as follows. The first thing we do is

adjust the color of the cable please read about the order of the wiring so you can follow the first we take is white orange make sure the cable is straight like this and fastened not folded but fastened like this then after white orange, we look for white green

make sure the bottom is not entangled, yes, for example, the bottom is not entangled, it's green, it's also attached, it's blue, we're looking for blue, the bottom is also not entangled, if there is a rope like this, just remove it first, it's green, it's blue, we're looking for it, it's blue, okay, it's like this, make sure it's attached,

green and blue it looks like it's still curled up, it's not a problem, we just stick it like this, then white and blue green like this, okay, it's already straight like this, if there is a little bend below, it won't be a problem, just take care of it,

then white chocolate last chocolate so like this so everything is in a tight condition like this orange white green blue green white white chocolate make sure the cable order is correct no one is wrong after this the next step is

we will cut it so that it is straight, not like this then we give a distance of about this so that later it is not too far from the connector of the iG45 we limit one clamp like this then we cut it straight make sure it's straight like this

Okay, it's straight, yes, okay, next we will, what is it called, we will unite it with the RG45 connector, yes, okay, next we prepare the RG45 connector, yes, we have prepared it, then we enter the position like this, not like this, yes, not like this, but like this, yes, enter from the left side, yes, like this,

then make sure it goes through, like this if we use this type of RG45 connector, it goes through inside so it's easier, there's a type of RG45 that doesn't go through but it's stuck to the end, so it's just like this

I will use the RG45 connector that we assume is not through, so I make sure it is only to the end like this then after that we put it into the connector of the RG45, sorry, into the pin pulse connector make sure it is not inverted, we put it in here like that

we pull a little so that it reaches the end then, don't let it come off again make sure it doesn't come off again so you push a little I don't push this because the cable is pierced so I don't push it too much so it doesn't pierce

make sure the RG connector is really stuck to the end so don't crimp it until the connector is really to the end if you have crimped as much power as this like that like this okay

Okay, if it's already connected, the IGBT-IMIN connector is already connected. When pulled like this, it doesn't come off. That means it's connected well. We will test later whether this installation is successful or not.

Okay, next you can do the same thing at the end of the one, I won't do it now, please do it according to what we have learned earlier, I will try to make this so that it saves more time, let's do it together, so I close the video first, later you can continue, so we meet again after the connector is united later, yes, with

UTP cable or the network cable until we meet again we continue so the two ends have become like this already connected between the cable and the RG45 connector make sure the order between the ends 1 and 2 are the same white orange orange, white green blue, white blue green, white chocolate, chocolate because we will arrange the wiring

straight means the ends of the cables are the same starting from white and orange after you do this then we will test whether our cable installation is successful or not by using the tester cable how do you pay attention here there are three here what you use is the RG45 this is for RG11

you enter it like this then you enter the other one like this, now we will test whether what we have done is successful or not, if this is successful, then when the first lamp turns on, then here too the first lamp will turn on straight, because it's straight, let's try, let's turn it on

see 1, 2, 3, 4, 5, 6, 7, 8 means the fourth cable color is already connected well the eighth cable color is already connected well it means the installation that we do for this stretch cable is successful

That's what we can do for today, hopefully you can follow it well. Insyaallah, maybe there will be failures that you will do, maybe. Because the first experience usually teaches a lot of things about failure. Stay patient and keep trying, don't give up.

Inshaallah there will be results later when you want to continue to pray. Don't forget to pray. Inshaallah Allah will make it easy. That's all maybe for this material. Hopefully it will be useful for all of us. I'm sorry for all the disadvantages.